CheckpointWest
Количка0
Процесор, активни спирачки и електроника

SA HAL ETU™ V2 електронен модул на спусъка – задно окабеляване

Марка
Specna Arms
Арт. №
SPARMS382

В наличност52 бр. на склад

41,52 €Цената е с ДДС.
1

  • Доставка: [СРОК]
  • Връщане: [СРОК ЗА ВРЪЩАНЕ]

Описание

Specna Arms HAL™ ETU V2 | Programmable electronic trigger unit

Specna Arms HAL™ ETU V2 is a programmable electronic trigger unit designed for V2 gearboxes, replacing conventional mechanical switching with a modern electronic system. This version features rear wiring and a T-Dean connector. It uses magnetic sensors operating on the Hall effect principle to detect the trigger position, so there is no mechanical contact or related wear of switching components when the trigger is detected. The unit allows you to set 5 trigger sensitivity levels ranging from 20–100% and 6 pre-cocking levels for faster response during single shots. It also features an active brake and several programmable modes for the SEMI and AUTO selector positions. SEMI can be configured to Semi, Binary, AUG or Sniper mode, while the AUTO position can operate in Auto, 3-round Burst or 5-round Burst mode. Settings are programmed directly using the trigger, so no mobile app or external programming cable is required. HAL™ ETU also provides electronic motor switching and offers protection against low voltage, overvoltage and excessively high RoF above 40 RPS. The unit is also compatible with modern brushless motors, such as Specna Arms Dark Matter or Warhead. For correct operation of the magnetic detection system, the supplied HAL™ trigger must be used.

Key features of the Specna Arms HAL™ ETU V2 electronic trigger unit

HAL™ ETU for V2 gearbox

The programmable ETU is designed for V2 gearboxes. This version features rear wiring and uses a T-Dean connector.

Hall sensors and adjustable trigger

Magnetic trigger position detection operates without mechanical contact. Sensitivity can be adjusted in 5 levels from 20 to 100% according to the desired trigger travel and shooting style.

Pre-cocking and active brake

There are 6 levels of pre-cocking for faster response on the next shot and an active brake for controlled motor stopping after the cycle is completed.

Programmable firing modes

The SEMI position can be assigned Semi, Binary, AUG or Sniper. The AUTO position offers Auto, 3-round Burst and 5-round Burst modes. Programming is performed directly using the trigger.

Brushless motor support and protective functions

HAL™ ETU is also compatible with modern brushless motors. The electronics also provide protection against low voltage, overvoltage and excessively high RoF above 40 RPS.

HAL™ ETU user guide

Programming functions and settings of the Specna Arms HAL™ ETU electronic trigger unit.

HAL™ ETU programmable firing modes

  • SEMI: Standard single shot.
  • Binary: Fires once when the trigger is pulled and once when it is released.
  • AUG: Mode simulating the two-stage trigger of the AUG platform.
  • Sniper: Mode designed for a single-shot firing configuration.
  • Auto: Automatic fire.
  • 3-Burst: 3-round burst.
  • 5-Burst: 5-round burst.

Important: When AUTO mode is selected, the gun first fires a 3-round burst when the trigger is pulled and then continues with unrestricted automatic fire if the trigger remains held. For correct operation of the HAL™ ETU magnetic detection system, the trigger supplied with the unit must be installed.

Activating the HAL™ ETU after installation

  • Set the fire selector to SAFE.
  • Connect the battery and wait for the first audible signal, approximately 3 seconds.
  • Pull and hold the trigger for approximately 5 seconds until the second audible signal.
  • Once activation is complete, the unit is ready for use.

Technical specifications

  • Manufacturer: Specna Arms
  • Model: HAL™ ETU V2
  • Type: Programmable electronic trigger unit (ETU)
  • Designed for: V2 gearbox
  • Wiring: Rear
  • Connector: T-Dean (male)
  • Detection method: Magnetic sensors (Hall effect)
  • Trigger sensitivity: 5 levels (20–100%)
  • Pre-cocking: 6 levels
  • Active brake: Yes
  • SEMI modes: Semi / Binary / AUG / Sniper
  • AUTO modes: Auto / 3-Burst / 5-Burst
  • Programming: Via trigger
  • Brushless motor support: Yes
  • Protective functions: Low voltage / overvoltage / RoF above 40 RPS
  • Weight: 24.5 g

Package contents

  • 1× Specna Arms HAL™ ETU V2 electronic trigger unit with rear wiring
  • 1× HAL™ trigger
  • 1× installation set of heat-shrink tubing and washers
  • 1× V2 selector plate
  • 1× programming card

Frequently asked questions (FAQ)

Which gearbox is the Specna Arms HAL™ ETU designed for?

This version is designed for V2 gearboxes and features rear wiring. Before installation, it is also advisable to check the available space inside the specific gearbox and gun body.

Is it necessary to use the trigger supplied with the HAL™ ETU?

Yes. The supplied HAL™ trigger is part of the magnetic detection system and must be installed for the unit to function correctly.

Can the HAL™ ETU be used with a brushless motor?

Yes. The unit supports modern brushless motors, such as Specna Arms Dark Matter or Warhead.

Do I need a mobile app to program the HAL™ ETU?

No. Functions are programmed directly using the trigger. No mobile app or external programming cable is required.

Which firing modes can be configured on the HAL™ ETU?

The SEMI position offers Semi, Binary, AUG and Sniper modes. The AUTO position can be assigned Auto, 3-round Burst or 5-round Burst. The unit also offers 5 trigger sensitivity levels and 6 pre-cocking levels.

Параметри

Параметри
ColorBlack / Combo
Gearbox versionV2
Connector typeT-Dean
Processor unitYES
Battery includedNO
02 // Още от сектора

Подобни продукти

Към магазина →