CheckpointWest
Количка0
Корпуси на гиърбокс

RetroArms ASG CZ Scorpion EVO 3 CNC гиърбокс

Марка
RetroArms
Арт. №
9572

В наличност1 бр. на склад

167,34 €Цената е с ДДС.
1

Това е всичко налично.

  • Доставка: [СРОК]
  • Връщане: [СРОК ЗА ВРЪЩАНЕ]

Описание

RetroArms CNC Gearbox for ASG CZ Scorpion EVO 3

RetroArms CNC upgrade gearbox for the ASG CZ Scorpion EVO 3 platform delivers outstanding strength and long-term reliability even with stronger springs. The shell is CNC machined from a single block of EN AW 7075 T651 aluminum, eliminating weak points typical for cast alloy gearboxes. The design is dimensioned for high-power setups, but its main benefit is improved stability, more precise gear alignment, and extended service life under standard and heavy load. The QSC system allows quick spring changes without full gearbox disassembly. Installation requires advanced technical skills, including gear shimming, AOE adjustment, correct motor engagement, and proper centering of the gearbox inside the receiver. This is not a plug-and-play replacement.

Key Features of RetroArms CNC Gearbox

Aircraft-Grade EN AW 7075 T651 Aluminum

Extremely strong material with higher resistance than standard steel and minimal deformation under load.

QSC Quick Spring Change

Change power level within seconds without opening the gearbox (stock must be removed).

Reinforced Front Section

Larger radius and stronger front area reduce the risk of cracking with high-power springs.

Improved Gear Seating

Reworked geometry improves gearbox compatibility and stability under heavy load.

New Wiring Routing

Separates wires from moving parts for safer electronics installation.

CZ EVO 3 CNC Gearbox Shell Example

CNC gearbox shell for CZ EVO 3 platform machined from a single aluminum block (surface finish may vary).

Technical Specifications

  • Model: AEG gearbox ASG CZ Scorpion EVO 3
  • Version: 2025+
  • Material: CNC EN AW 7075 T651 aluminum
  • Bearing Hole Diameter: 8 mm (AntiRot holes)
  • Compatibility: ASG CZ Scorpion EVO 3 A1 (all versions)
  • Compatible Electronics: ASG EVO control units, JeffTron Leviathan EVO
  • Recommended Torque: Max 1.2 Nm

Package Contents

  • RetroArms CNC gearbox ASG CZ EVO 3 QSC
  • Screw set
  • QSC spring guide

Warning

  • Do not use cylinder heads with rubber front buffers (MAXX, FPS Softair), as damage to pins may occur.
  • Bearing holes are 0.02 mm smaller for tight fit; standard bearings should be glued.
  • Installation requires advanced technical experience and correct gearbox centering.

Frequently Asked Questions (FAQ)

Which Airsoft Guns Is the RetroArms CNC Gearbox Designed For?

The gearbox is designed for ASG CZ Scorpion EVO 3 AEG airsoft guns and is compatible with all models in this series.

Is the Gearbox Designed for 8mm Bearings?

Yes, the gearbox is designed for 8mm bearings. The bearing holes are intentionally 0.02 mm smaller to provide a tighter fit and help prevent the bearings from rotating. When using standard bearings, the manufacturer recommends securing them with a suitable adhesive.

Can a Cylinder Head With a Rubber Buffer Be Used?

No. The manufacturer does not recommend using cylinder heads with a rubber buffer on the front, such as some MAXX or FPS Softair models. The buffer may cause damage to the cylinder head locating pins.

Is the RetroArms CNC Gearbox a Plug-and-Play Replacement?

No, installation requires advanced technical experience. During assembly, the gears must be properly shimmed, the AOE and motor engagement must be adjusted, and the gearbox must then be correctly centred in the gun body. We therefore recommend having it installed by an experienced airsoft technician.

Параметри

Параметри
ColorSilver
Body/receiver materialMetal
Gearbox versionEVO
Bearings (mm)8 (mm)
Spring guideMetal
02 // Още от сектора

Подобни продукти

Към магазина →