GUARDER Shim Set (18 pcs)
Out of stock
It cannot be ordered right now.
- Delivery: [TIME]
- Returns: [RETURN PERIOD]
Description
GUARDER Shim Set
GUARDER shim set is designed for precise adjustment of gear positions in an AEG gearbox. The set contains a total of 18 shims in three thicknesses – 0.15 / 0.3 / 0.5 mm, allowing you to adjust the play of individual gears using a suitable combination during servicing. Correct shimming is important for smooth gear operation: the gears should not have excessive lateral play, but at the same time the shims must not bind them so tightly that they become difficult to rotate after the gearbox is tightened. From our experience, it is best to start with the thinnest shims and check the free movement of the gears in the fully tightened gearbox after each adjustment. The shims are made from S316 stainless steel and have an inner diameter of 3 mm. The complete set weighs 4 g.
Key Features
18 Shims in One Set
The set contains a total of 18 shims – six pieces of each thickness for gradual gear adjustment.
Three Different Thicknesses
Shims are available in 0.15 / 0.3 / 0.5 mm thicknesses, which can be combined according to the requirements of the specific gearbox.
S316 Stainless Steel
GUARDER manufactures the shims from S316 stainless steel, which provides good resistance to wear during regular servicing.
Precise Gear Positioning
Correctly selected shims help adjust the lateral play and relative position of the gears so that they can rotate freely and mesh correctly.
3 mm Inner Diameter
The shims have an inner diameter of 3 mm and are designed for corresponding gear axles in AEG gearboxes.
ANAREUS Gear Shimming Tip
Mass-produced guns often have poorly adjusted gear shimming, so it is worth shimming the gears correctly during the first service. This involves placing shims of different thicknesses between the gear and bearing in the gearbox to eliminate play between the gear and gearbox. At the same time, however, you must not over-shim the gears, as this would cause them to bind. Therefore, using a trial-and-error method, you add and remove shims, often in increments of 0.1 mm, until you achieve ideal shimming, where the gear has minimal to almost no play in a fully closed gearbox (this must be tested with the gearbox fully closed and tightened) while still rotating freely under its own inertia with minimal resistance (the gears must not be lubricated with grease or any other oil during testing). When shimming individual gears, you must also make sure that the gears do not rub against the gearbox shell or against each other, so you also need to check the height of the individual gears relative to one another. In addition, you must check the position of the bevel gear relative to the motor pinion so that the bevel gear is not too low, causing the motor to force it out of alignment, or too high, causing the motor pinion to wear the edges of the gear teeth. There is still more to consider: you also need to check the position of the sector gear relative to the piston teeth so that the gear pulls the piston through the center of its teeth rather than along their edges, which could otherwise cause contact with the piston body or damage to the gear teeth. Some technicians start shimming with the spur gear because it sits vertically beneath the other gears, but this method increases the risk of incorrect bevel gear positioning relative to the motor pinion. Although enough teeth will usually still engage to prevent immediate damage, it can result in worse motor sound, higher battery current draw and reduced RoF. The second method is shimming from the bevel gear, but you must position the bevel gear high enough that it does not rub against the spur gear while also ensuring that the spur gear does not rub against the gearbox. Both methods have their supporters and critics, as well as their own advantages and disadvantages. In short, gear shimming is an art that separates home tinkerers from true professionals in AEG upgrades.
Technical Specifications
- Type: gear shims
- Material: S316 stainless steel
- Thicknesses: 0.15 / 0.3 / 0.5 mm
- Inner diameter: 3 mm
- 0.15 mm version: large outer diameter
- 0.3 mm version: small outer diameter
- 0.5 mm version: small outer diameter
- Set weight: 4 g
Package Contents
- 6× 0.15 mm shim – large diameter
- 6× 0.3 mm shim – small diameter
- 6× 0.5 mm shim – small diameter
Frequently Asked Questions (FAQ)
What Are Shims Used for in a Gearbox?
Shims are used to adjust the position and lateral play of the gears. The aim is to ensure that the gears mesh correctly, do not have excessive play and can still rotate freely once the gearbox is assembled.
Why Does the Set Include Several Different Thicknesses?
Every gearbox, bearing and gear set can have slightly different dimensions and tolerances. The 0.15 / 0.3 / 0.5 mm shims can be combined to adjust the required spacing more precisely.
How Do I Know if the Gears Are Shimmed Correctly?
With the gearbox tightened, the gears should rotate freely without binding while also having no excessive lateral play. During servicing, we recommend checking the adjustment gradually, as too many shims can bind the gears and increase resistance throughout the mechanism.
Do I Need to Shim the Gears Again When Replacing Them?
Yes, this is recommended. New gears, bearings or the gearbox shell itself may have different manufacturing tolerances, so the original shim arrangement may not be suitable for the new setup.
Specifications
| Color | Silver |
|---|---|
| Body/receiver material | Metal |
| Počet kusů v balení | 18 |




